Electric Warmer Pump

2500W ZVS Heater Induction Heating Board Module + Coil + Pump


2500W ZVS Heater Induction Heating Board Module + Coil + Pump
2500W ZVS Heater Induction Heating Board Module + Coil + Pump
2500W ZVS Heater Induction Heating Board Module + Coil + Pump
2500W ZVS Heater Induction Heating Board Module + Coil + Pump
2500W ZVS Heater Induction Heating Board Module + Coil + Pump
2500W ZVS Heater Induction Heating Board Module + Coil + Pump
2500W ZVS Heater Induction Heating Board Module + Coil + Pump
2500W ZVS Heater Induction Heating Board Module + Coil + Pump

2500W ZVS Heater Induction Heating Board Module + Coil + Pump   2500W ZVS Heater Induction Heating Board Module + Coil + Pump

2500W ZVS Heater Induction Heating Board Module + Coil + Pump. Input voltage: 12V-48 recommended above 36V. Power requirements: less than 12V 10A 15V or more 20A.

For induction heating, it is recommended to use a switching power supply of 48V50A or higher. If the power supply is 24V or more, a power supply of 20A or more is required.

The higher the voltage, the larger the current, the higher the heating power, the faster the heating speed. The heating plate is made of 240120mm military grade PCB, and the performance is stable. The power line is fully covered with copper cover design, which can increase the current and heat generation. Using an oversized and large power heat sink, the heat dissipation is better.

The output uses three M4 copper columns in parallel, which can be connected to other outputs such as high voltage packages. Six IRFP260 and 12 capacitors are used in parallel resonance, which has high power efficiency. Buyers must see / pay special attention. The power of induction heating is very large. In addition to the heat generated by the board and components, the heat generated by the copper tube is also very large.

Buyers can bring their own water-cooled cooling system. It must be noted when using a switching power supply, because a high-power switching power supply generally has a slow-start function, that is, it slowly rises when the output voltage starts, and if the voltage rises to 10V, the induction heating circuit is turned on because If the voltage is not enough, the circuit will not vibrate, so that the two MOS tubes are turned on at the same time to burn the components. Therefore, it is necessary to connect the induction heating circuit after the switching power supply voltage is stable.

When heating metal objects, try not to heat the metal with too much volume. Otherwise, the overload may occur due to power overload. It is better to add a 50A fuse or ammeter and air switch when using. Although this driver board can withstand more than 50A current, it is recommended not to exceed 48V55A in order to prevent accidents and damage for long-term continuous operation. The heating coil of the package has a diameter of 60mm and a design voltage of 86V. If a voltage of 40V or more is used, the heating coil with an inner diameter of 60mm or more must be used.

The pump uses a 12V DC power supply. Please use the voltage regulator module to supply power separately to avoid burning the fan. For induction heating, the copper tube in the package of this product should be used, or it should be wound according to the standard of 10 mm inner diameter of 60mm.

This heating module is designed to be used in environments above 2000W. 2-4 Business Dayscustomized item except.

Buyers are responsible for these charges. The item "2500W ZVS Heater Induction Heating Board Module + Coil + Pump" is in sale since Tuesday, December 18, 2018.

This item is in the category "Business & Industrial\Electrical Equipment & Supplies\Electronic Components & Semiconductors\Semiconductors & Actives\Power Regulators & Converters". The seller is "newlemonlife" and is located in zhengzhou. This item can be shipped worldwide.
  1. Brand: JINNUO
  2. Country/Region of Manufacture: China
  3. DIY Supplies: Electrical
  4. Conversion Direction: Step-Up
  5. Product Type: Power Converter
  6. Device Function: Voltage Converter
  7. MPN: Does Not Apply
  8. Current Conversion: DC to DC
  9. Model: ZVS2500W
  10. Size: 120*240*105 mm
  11. Material: none
  12. Features: Induction Heating
  13. Color: Black
  14. Energy Star: Not Compliant
  15. Type: ZVS Heater

2500W ZVS Heater Induction Heating Board Module + Coil + Pump   2500W ZVS Heater Induction Heating Board Module + Coil + Pump